Industrial Aerosols

Product Details:

Product DescriptionIT-1098  Motorcycles are high-speed applications that operate in tough conditions like rain, dirt, sand, and high shock loads. These specially developed chains are used as the part of the drive train to transmit the motor power to the back wheel. The chain must never be run dry. Lubricating the chain regularly prolongs its life. IT-1098 is based on synthetic oils containing oil soluble organo-moly compounds. It goes on to wet to penetrate parts deeply, setting up an adhesive lubricating coating that does not fling-off at high speeds. The protective coating set up on the outer of the chains protects against the corrosion and weathering effects.

Product Details:

IT-1105 is a bright zinc based coating designed to prevent rust and corrosion on all types of metals for up to two years. It works electro-chemically on all ferrous metals, providing rust and corrosion protection indoors and outdoors. The coating is designed to blend in color with the previous hot-dip galvanized portions of the parts. This can also be used as a primer over rusted metal to repair hot dip galvanizing. Specially formulated, it provides a tough, flexible coating that will not crack or peel even in extreme heat or cold.

Product Details:

Product DescriptionIT-1084 is designed to provide thin layered coating onto the printed circuits or other electronic substrates to protect and significantly extend the life of the components and circuitry against environmental and mechanical damages. The coatings protect electronic printed circuit boards from moisture and contaminants, preventing short circuits and corrosion of conductors and solder joints.

Product Details:

Product DescriptionIT-1100 is a fast evaporating, non-chlorinated precision cleaner spray for online cleaning of electrical/electronic components. Examples of applications: for cleaning distribution boards, switches, relays, potentiometers, plug-in connections, sliding and screw contacts & PCB's.

Product Details:

Zinc-Aluminium coating to prevent rust and corrosion on all types of metals. This can also be used as a primer over rusted metal to repair hot dip galvanizing. It provides a tough, flexible coating that will not crack or peel even in extreme heat or cold.

Product Details:

IT-1123 is a fast drying, non-flammable, ultra high strength “on line” dielectric cleaner. Non-flammable with no flash point & non-corrosive, the cleaner is fast drying and dissolves the grease, grim and other contaminants fast leaving the surfaces clean and dry. It is safe on most metals and Bakelite but not recommended for use on “Plastics”

Product Details:

Product DescriptionIT-1095 is designed as a non-staining cleaner/lubricant for modern textile machinery used for various operations such as spinning, winding weaving and knitting etc. The product is designed using select combinations of cleansing, corrosion protection and lubricating materials. Protects scissors & cutters of splicers / knotters against rust & corrosion and reduces the wear & tear of moving parts.

Product Details:

Product DescriptionIT-1097 is a High temperature synthetic adhesive chain oil spray designed lubrication of the chains and wire ropes exposed to high speeds, water/sea-water contamination. It gives excellent protection against corrosion & wear. Tack additives prevent the lubricant getting thrown of at high speeds. The lubricant is neutral to ‘O’ rings.

Product Details:

Product DescriptionIT-1101 is a precision cleaner solvent based on HFC fluid with zero ozone-depletion and a low global warming potential is designed for precision cleaning of the electronic components. It is ideally suited for cleaning fine particulate matter (submicron range) from metal and nonmetal parts. Typical applications include: as a cleaning and rinsing agent, as drying fluid, for particulate removal or as a dielectric fluid etc. It replaces for many HCFC, PFC, and CFC-113 applications.

Product Details:

IT-7400 is stable, high performance synthetic oil designed for high temperature applications

Product Details:

Product DescriptionIT-1096 is designed to provide long-term, smooth lubricating action under extremes of loads and temperatures - it also helps protect metal parts from rust and corrosion when subjected to humidity and corrosive atmosphere. The product is based on solid lubricant powders, synthetic oils and various additives for wear protection and efficient lubrication of sideways & cams.

Product Details:

Product DescriptionIT-5001, a high-purity precision liquid is a best available best available replacement to CFC11. Compared to CFC11, IT-5001 is approximately ten times less harmful to stratospheric ozone and is therefore recognized as a viable solution allowing the rapid phase-out of CFCs. Although. IT-5001 is the only available “near drop-in” alternative, it is not a direct substitute as IT-5001 is a more polar molecule than CFC11.
Additional Information

Product Details:

Product DescriptionMixture of silicone and a cleaner/wiper solvent designed as an anti-stick agent for facilitating cleaning of residues which have accumulated on the spinneret head.

Product Details:

IT-2595, a high performance anti-corrosion coating designed for protection of the components stored outdoors, provides an excellent protection to metal substrates. It leaves wax-like film which is flexible and non-migratory. The coating can be removed with any mineral spirits or alkaline cleaners such as Ultrachem Degreaser. A film thickness of at least 50-70 microns is recommended for protection of parts in uncovered outdoor storage. IT-2595 can be applied by dipping brushing or spraying.

Product Details:

Product Description

Chemlube Synthetic Chain Oils are designed for a wide variety of chain applications where heat is a major factor. When used in the proper application, they protect against wear. Some contain a unique high temperature organo-molybdenum extreme pressure anti-wear additive that acts to protect the chain under the most adverse conditions. This, combined with the natural detergency of the oil and its affinity or polarity with metal surfaces, combines to keep oven chains clean and lubricated properly. Our technical staff can recommend oils based on your requirements and application methods.

Product Details:

IT-5002  A high-purity, di-electric, non-chlorinated, odour-less solvent designed for cleaning of electrical & electronic equipment like motors, it exhibits an efficient residue-free cleaning. The cleaner is safe to use for all metals, plastics, varnishes, rubbers etc. Cleaning is done by dip tank, wipe-off or with forced air. It is a slow drying cleaning solvent that cuts into the grease & grime effectively & exhibits enhanced penetration.

Additional Information:

• Item Code: IT-5002

Product Details:

Product DescriptionIT-2588 is flexible coating specially formulated for use on electrical equipment. It protects against moisture and corrosion. It possesses high arc-resistance and insulating properties. It is successfully used in applications that range from class 105 to 220. The product penetrates thoroughly and forms a tough, flexible film which has a high arc resistance and non-tracking properties. The coating resists oil, water, acids and alkalis & has an excellent adhesion. It is oil resistant & can be thinned with low cost solvents. The coating is used for motor, stator, coil and transformer impregnation. Controller shafts, finger blocks, switch bases, and other electrical insulation, switch parts (porcelain molded compound, etc.). It is also used for field coils, windings and machine frames, inside motor frames, commutator parts, collector rings, enameled wire coils. For sealing oil lines, air lines, threaded pipe joints, transformer drain taps, gaskets, etc.

Product Details:

Description

IT-1102 is a zinc rich coating that performs like a hot dip galvanized coating to prevent rust and corrosion on all types of metals for up to two years. It works electro-chemically on all ferrous metals providing rust and corrosion protection indoors and outdoors.

Product Details:

We wish to offer our IT-1093 as a replacement grade to this requirement of yours. Kindly review the following and attached sheets for additional information on our are offering.

 

IT-1093 is an all-round spray and used in all industrial and workshop areas. Due to its special formula, the product offers and very low coefficient of friction, corrosion protection, cleaning, water resistance, lubrication, and conservation – all combined in one product.

Applications:

·         Loosens seized screw connections, bolts, fittings, and valves

·         Dispels moisture from electrical lines

·         Prevents leakage current and simplifies the starting of wet motors

·         Eliminates the squeaking and creaking of hinges, guides, bearings, and all kinds of joints and couplings

·         Cleans dirty surfaces and leaves behind an extremely thin film that does not smear, stick, or attract dust

·         Protects and cares for all tools, machines, electrical and mechanical precision instruments (measurement tools, locks, and weapons) and keeps them functional

IT-1093 is silicone-free and resists all atmospheric influences due to weather. It is used in workshops, automobiles, navigation, electrical systems, agriculture, household, and hobbies etc.

 

Product Details:

IT-1092 Dry Film Graphite Lubricant Aerosol features high lubricity and adheres to most surfaces with minimum surface preparation. The coating is conductive which air-dries rapidly at room temperature to provide clean lubrication. IT-1092 may be used where both lubrication and electrical properties are required.IT-1092 provides a long term lubrication and protects against extreme pressures and temperatures and is used for lubrication of sliding surfaces exposed to dust or water. It contains a high level of pure and fine graphite powder which results in a good electrical conductivity, as well as gliding and release agent properties. The coating exhibits good adhesion on metal, many plastics, glass and wood.

Product Details:

IT-2597, a high performance anti-corrosion coating designed for protection of the components stored outdoors, provides an excellent protection to metal substrates. It leaves a thin wax-like dry to touch film which is flexible and non-migratory. The coating can be removed with any mineral spirits or alkaline cleaners such as Ultrachem degreaser. A film thickness of at least 50-70 microns is recommended for protection of parts in uncovered outdoor storage. IT-2597 can be applied by dipping brushing or spraying